Re: Keyword 0808

Hi
Well, As Far as I know, VW uses the two protocols ISO 9141 with
KWP1281 and KWP1271 and ISO 14230 with KWP2000, if you don't believe
me just try to communicate with a Seat Leon ABS ECU.
My VW GOL Diesel 2000 uses ISO9141 with Keywords 01 8A, also I saw
keywords 0x89 0x77 (VW USA).
Then I thougt that for erasing DTCs you send 0x03 0xZZ (Block
Counter) 0x05 (erase DTC) and 0x03, each byte has to be acknoledge.
What is the difference between ISO9141 and ISO9141-2? Isn't it the
same protocol?
Bye
Ezequiel

--- In opendiag@yahoogroups.com, "Bülent Özen" <ozenelekt@i...>
wrote:
> hi Ezequiel
>
> 1.) VW use the protocol KWP1281 ( nothing to do with KWp2000 ).
But if an VW ECU responds to fonctional ECU Add. 0x33 ( e.g passat
1999 ) you can communicate with ISO9141-2 too.
>
> 2.) KWP2000 ( after ISO14230 ) must use the keywords 0x8f and 0xE9
or ( 0xex manufacturer specifique ) also only ISO 9141-2 use the
keywords 0808 or 9494
>
> 3.) this command sequence that i described is figured in ISO9141-2
page 14.
>
> 4.) we have tested this car too with our mOByDic chip . it runs
only with ISO9141-2
>
> best regards
>
> Bülent
>
>
>
> ----- Original Message -----
> From: acetoel
> To: opendiag@yahoogroups.com
> Sent: Sunday, July 13, 2003 7:59 PM
> Subject: [opendiag] Re: Keyword 0808
>
>
> Sorry but you are not reight. That command sequence corresponse
to
> ISO 14230 (also known as KWP2000 for VW) and not to ISO 9141
(also
> known as KWP1281 or 1271 for VW).
> Bye
>
> --- In opendiag@yahoogroups.com, "Bülent Özen" <ozenelekt@i...>
> wrote:
> > hi Andreas
> >
> > i have explained how an ISO9141-2 will be initialized in a
recent
> message in
> > opendiag archive. i uploaded a file ISO9141 in file section of
> opendiag for
> > introduction and signal level.
> > after an succefully init you send ( 10400 baud ) to ECU
> >
> > 0x68 0x6A 0xF1 0x03 CS to read the
DTC
> >
> > response 0x48 0x6B ECUAdd 0x43
> DTC1highbyte
> > DTC1lowbyte .................. CS
> >
> > 0x68 0x6A 0xF1 0x04 CS to clear DTCs
> >
> > response 0x48 0x6B ECUadd 0x44 CS
> >
> >
> > regards
> >
> > Bülent
> >
> >
> >
> >
> > ----- Original Message -----
> > From: "Andreas Siemering" <student@a...>
> > To: <opendiag@yahoogroups.com>
> > Sent: Saturday, July 12, 2003 8:13 PM
> > Subject: RE: [opendiag] Keyword 0808
> >
> >
> > > Hi Bülent,
> > >
> > > thanks for your help. Is there any documentation about
> > > ISO9141-2 communication available on the web? Because
> > > I have no idea how to establish communication since
> > > none of the programms worked. Maybe with some papers
> > > I can start develop my own application. At the moment
> > > I am only interested in reading and deleting fault codes.
> > >
> > > Regards
> > > Andreas
> > >
> > >
> > >
> > > To unsubscribe from this group, send an email to:
> > > opendiag-unsubscribe@egroups.com
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> > >
> > >
> > >
>
>
> Yahoo! Groups Sponsor
> ADVERTISEMENT
>
>
>
>
> To unsubscribe from this group, send an email to:
> opendiag-unsubscribe@egroups.com
>
>
>
> Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.
>
>
> [Non-text portions of this message have been removed]

 
Received on Tue Jul 15 03:16:51 2003