Re: [opendiag] 1995 Opel diagnostic strategy change

That is okay but it is not the same pinout in all opel cars,it have different by corsa,vectra,tigra and astra in pinout of K lines for airbag and dash and other.
7pin of obd2 - engine vectra dashboard K line
12pin of obd2 - airbag,dashboard vectra airbag K line
3 pin of obd2- immo

DIAGNOSTIC CONNECTOR OBD-2 OPEL
4,5---GND
16----+12 POWER
3-----IMMOBILIZER,ALARM
6+7---ENGINE ECU [K+L-LINE]
8-----MULTYDISPLAY,AUTORADIO
12----ABS,AIRBAG (vectra,tigra)
7-----AIRBAG (omega)
13 or 14 - for Astra
(This sw don`t work in Astra-G after 98 year)
Opel Tigra 97 12 pin OBD2 je Airbag

GM Siemens SRS Unit 90 569 350
dbs 0002552N 27/97 05
PROCESSOR MC68HC11[4E28B] O/CE 846793

PIN IMITATION AIRBAG
PIN 1,2 -- AIRBAG DRIVER -- R=1,5 OHM
PIN 3,4 -- AIRBAG PASSANGER -- R=1,5 OHM
PIN 10,11--AIRBAG SIDE DR -- R=1,5 OHM
PIN 13,14--AIRBAG SIDE PS --R=1,5 OHM
PIN 8,9 --LENTA 1--R=3,1 OHM
PIN 15,45--LENTA 2--R=3,1 OHM
PIN 41,42,43,44 - SENSOR

PIN 5 -- +12 IGNITION
PIN 6 -- AIRBAG LAMP
PIN 7 -- GND
PIN 12 -- DIAG

----- Original Message -----
From: Page, John
To: 'opendiag@yahoogroups.com'
Sent: Monday, October 13, 2003 2:58 PM
Subject: [opendiag] 1995 Opel diagnostic strategy change

Up until about 1995, there was one diagnostic lead (ALDL 10-pin plug pin G) for all Opel/Vauxhall systems. In about 1995, the diagnostic lead was divided up, and later models used up to 4 separate K-lines within a 16-pin plug. This was progressively introduced for all vehicles.

The reason for this was that to meet the specifications, each control unit must have an input resistance of 1k ohms on the diagnostic lead, and as these are in parallel on the diagnostic lead reliable connection could not be achieved with more than 10 control units connected. The division into 4 diagnostic lines was made to allow simultaneous communication with linked control units. For example, the engine control unit is one one lead, the transmission control unit is on another, and the ABS control unit is on a third. These separate leads are designated K-lines.

The 16-pin connector pin allocations are:
1 - unoccupied
2 - unoccupied
3 - diagnostic lead (automatic transmission, central door locking, electric sliding roof)
4 - earth
5 - earth
6 - blink code (engine control unit)
7 - diagnostic lead (electric seat, engine control unit)
8 - diagnostic lead (cruise control, TID/MID, ATWS/immobiliser)
9 - unoccupied
10 - unoccupied
11 - unoccupied
12 - diagnostic lead (airbag, ABS)
13 - unoccupied
14 - unoccupied
15 - unoccupied
16 - +12V

Hope this helps someone...
John

Yahoo! Groups Sponsor

To unsubscribe from this group, send an email to:
opendiag-unsubscribe@egroups.com

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

[Non-text portions of this message have been removed]

 
Received on Mon Oct 13 07:53:32 2003